Corrections: Backseat Babysitter (PBA256)

June 23. 2020

On patterns dated before 062320 (see date in middle at bottom of each page), please make these corrections:

​Page 3, StepII-B:

​ ​This section provides General Binding Instructions for the project. Rather than being labeled as step B, they should've just been shown in a box as supplemental information.

​Page 4-5, Step G:

​ ​Steps G-5, 6, and 7 apply to both Pocket F and Pocket G. You will make Pocket G in the same basic way as you did Pocket F, except that you'll bind the opposite edge (see step 10).

June 22, 2020

On patterns dated before 062220 (see date in middle at bottom of each page), please make these corrections:

​Page 5, Step II-G-8:

​ ​Change the text to read as follows:

​ ​ ​8. Working from the LINING side of the pocket, bind the LEFT edge of Pocket F

​ ​ ​Using the 2" x 7" Pocket F Side Binding, turning the binding over to cover the edge at the top of the pocket and binding past the seam on the bottom (figure 22).

​ ​ ​Also, please note that the binding along the right side in figure 22 should properly be on the LEFT side when viewed from the lining side.

​Page 6, Step II-H-6-b:

​ ​Change the text to read as follows:

​ ​ ​b. On the seamed side of each strap, mark vertical lines from top to bottom ¼" and 4¼" in from the finished end (figure 25).

​ ​​NOTE: Figure 25 is correct.

​Page 6, step II-H-6-d: 

​ ​Change the first sentence to read as follows:

​ ​ ​d. Center the loop (soft) side of the 3½" piece of hook-and-loop tape on the seamed side of each strap to the inside of the line marked 4¼" in from the finished end.

​Page 6, Step II-H-6-e:

​ ​Change the text to read as follows:

​ ​ ​e. Attach a D-ring to each Stroller Strap.

​ ​ ​ ​i. On the other end of each strap, mark vertical lines on the seamed side of the strap 1" and 2¼" in from the raw edge (figure 28). On the unseamed side, mark a vertical line 2¼" in from the raw edge (figure 28).

​ ​ ​ ​ii. With unseamed side of strap up, insert the strap into the opening of a 1" D-ring. Bring the seamed sides of the strap together with the ring in between, aligning the 1” and 2¼” marked lines on the seamed side. On the unseamed side of the strap, stitch across the strap on the 2¼” marked line to secure the D-ring in place, back­stitching at each end (figure 29). Set straps aside.

​Page 8, step III-G-2-b:

​ ​Change the last sentence to read as follows:

​ ​ ​Stitch the strap to the organizer along, sewing ⅛" from the raw edge.

​Page 9, step III-G-2-c:

​ ​Change the last sentence to read as follows:

​ ​ ​Stitch the strap to the organizer along, sewing ⅛" from the raw edge.

The First Printing:

On the first printing of this pattern, please make this correction:

​Page 9:

​ ​The drawing on Figure 9 shows the various straps extending beyond the organizer. The stroller straps (in the middle) show one with the hook-and-loop fastener up and the other with the hook-and-loop down.

​ ​Both stroller straps should look like the strap on the left. The hook-and-loop fastener will be DOWN on both straps.